Ground
See Also: Earth, Soil, Ground Penetrating Radars
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
Stator Ground Protection Relay
SEL-2664S
-
Schweitzer Engineering Laboratories, Inc.
Protect high-impedance grounded generators from ground faults at standstill, during startup, and while running with the multisine frequency injection and neutral overvoltage-based protection in the SEL-2664S.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
779517-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Relays, Switches, Sensors
-
CR Magnetics Sensing Relays and Switches provide a simple method of monitoring electrical properties and alerting a system to a fault or event condition. These products are available with a wide variety of configurations, including time delays, various output styles and logic. From simple proving switches, to fully featured high performance ground fault sensing.
-
Product
Mixed Signal Oscilloscopes
-
Fully configured USB 2.0 oscilloscope - 14 bit 100 MSa/s, 2 analog channels, 8 digital inputs, External Trigger, 8M samples storage for each of the 2 analog and 8 digital channels, CS700 Signal Generator (0-10MHz, Sine, Square, Triangle). Complete with the CS300 application software, 2 x CS1001 and CS1004/5 probe sets. The front panel ground is continuous via the USB ground to the PC.
-
Product
3U 5-Slots OpenVPX P&G, w/o ROHS, 3.125G
101VPX305P-9K05
-
3U 5-Slots OpenVPX Power & Ground, Pass through, conformal coating, w/o ROHS, Max data rate (Gbps) 3.125.
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
43-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Multibeam Echosounder - Subsea
SeaBat T50-S
-
The T50-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with a Subsea Sonar (SSP), the T50-S produces unprecedented clean data, providing faster operational surveys and reduced processing time in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 kV Isolation
43-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
NI-9205, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
779357-01
Voltage Input Module
±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The NI‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the NI‑9205 includes up to 60 V of overvoltage protection between input channels and common. In addition, the NI‑9205 also includes a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection.
-
Product
3U cPCI Intel SBC
75INT2
-
NAI’s 75INT2 is a 3U cPCI Intel® Core™ i7-based, Single Board Computer (SBC) that can be configured with up to two intelligent function modules and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.NAI's Intel® Core™ i7 SBCs in the 3U cPCI form factor offer improved processor performance and better security, targeted at military and defense applications such as manned and un-manned air and ground vehicles, and in more sophisticated digital signal processing applications such as intelligence, surveillance, reconnaissance, radar and sonar.
-
Product
Earth Resistance
-
Precision Mastech Enterprises Co.
Specialized instruments designed to measure the effectiveness of earthing systems, ensuring electrical fault currents safely dissipate into the ground to protect people and equipment.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
AC & DC Aging Test Equipment for Arrester Valve Plate
-
Shanghai Guantu Technology Co., Ltd.
The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.
-
Product
Plugbord
3682-4
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. Interleaved buses pattern on wiring side, solder coated for user convenience. Overall ground plane with clearance around each hole on component side. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board. Row and column legends provided.
-
Product
Multibeam Echosounder - Subsea
SeaBat T20-S
-
The T20-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with the all-new Subsea Sonar Processor the T20-S provides the highest quality survey data in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel. Smaller form factor and reduced operational power to extend mission time for battery powered underwater vehicles. Internal data storage for self-contained survey solution, and interfacing via standard Ethernet to reduce integration time.
-
Product
3U 1-Slot OpenVPX P&G, Aperture J
101V301P05-9X12R
-
3U 1-Slot OpenVPX Power & Ground, Aperture J, Supports VITA 67.3D , Pass through, w/ROHS, Max data rate (Gbps) 10.
-
-
Product
VHF/UHF Nav/Flight Analyzer
EVSF1000
Analyzer
The R&S®EVSF1000 is a signal level and modulation analyzer for installation in flight inspection aircraft. It performs measurements on ILS, VOR and marker beacon ground stations during startup, maintenance and servicing and analyzes ATC COM signals.
-
Product
Electric Fence Chargers
Mark 8
-
Parker McCrory Manufacturing Co.
The all new Mark 8, low impedance fencer gives you the stock holding power that you have always wanted. Shocks right through wet weeds or brush and over extremely dry ground. Features Parmak`s exclusive built-in DIGITAL performance meter that tells you the exact condition of the fence. Takes the guesswork out of electric fencing. 100% solid state, with all new low impedance, uni-junction circuitry. No moving parts. Ideal for use with high tensile single or multi-wire fences. New color coded fence and ground terminals. Red to the fence and Black to ground. The Mark 8 operates for less than 7 cents a month at 7 cents per kwh. Fuse protection, with new built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
Product
Co-Siting Filters and Combiners
-
*Multiplexers, Duplexers, Diplexers and Antenna Sharing Combiners*Enables multiple base stations to share a single antenna*Many of the units offer both High and Low band support*Ideal solutions for either ground based and tower based antenna sharing*Compact lightweight rugged construction
-
Product
Power Supply
-
Power supplies of various ratings for Air, Naval ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factor designs.Most products qualified to requirements of MIL-STD-461C and MIL-STD-810D or the equivalent JSS 55555 are designed and manufactured. Airborne versions are designed to meet MIL-STD-704D. Specific design constraints are handled with respect to long time storage life and suitability for air cooled or conduction cooled applications. Designs suitable for high power supplies of various ratings for Air, Naval, Ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factors designs.
-
Product
SpaceWire Isolator
134
-
The SpaceWire Isolator is an isolation unit for ground test and integration applications, providing galvanic isolation for two SpaceWire links. Isolation is tested to 60 V with components rated to 100 V and 2500 V max transient voltage.
-
Product
Surge Voltage Generator
SSG 1100
-
Cable fault location with the BAUR SSG 1100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
VHF/UHF Nav/Drone Analyzer
EVSD1000
Analyzer
The R&S®EVSD1000 VHF/UHF nav/drone analyzer is a signal level and modulation analyzer for use aboard medium sized drones. It measures ILS, GBAS and VOR ground stations during startup, maintenance and servicing and analyzes air traffic control communications (ATC COM) signals. The mechanical and electrical design is optimized for drone based measurements of terrestrial navigation systems.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
Neutrino Ground ISR
SX12 ISR1200
-
The Neutrino SX12 ISR1200 is the inaugural series model. With a 1280×1024/12 µm resolution focal plane array (FPA), a 120 mm to 1,200mm CZ lens, and advanced image processing, it is the ideal OEM camera module for integration into long-range ground ISR, perimeter surveillance, border surveillance, and counter-UAS (CUAS) systems.
-
Product
Voltage Probe
KHZ43201
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
Product
Handheld Micro-Ohmmeters
RMO-H Series
-
The RMO-H is battery operated and handheld micro-ohmmeter. It is designed for a variety of applications for contact resistance measurement of non-inductive test objects. Typical applications are accurate testing of:medium and high-voltage circuit breakers,disconnecting switches,high-current bus bar joints,cable splices,and different high-current links.Even more, it accurately measures in high-induction filed environments and substations, as well as in factory testing.RMO-H Series contains six models in total, divided in 2 sub-series depending on the test leads length requirement and the battery type:RMO-H1, RMO-H2 and RMO-H3 models are intended for use with short cables (e.g. 1,3 m / 3 m / 5 m). The 1-cell Li-Po battery with 8200 mAh capacity provides output voltage up to 4,1 V DC.RMO-H21, RMO-H22 and RMO-H23 models are ideal for applications where test leads with lengths > 5 m are required. The high output voltage (up to 8,3 V DC) is provided by 2-cells 4100 mAh Li-Po battery.The test current is regulated and can be selected in a range of 1 A to maximum 300 A, depending on the maximum test current rating:RMO-H1, RMO-H21 models – up to 100 A DCRMO-H2, RMO-H22 models – up to 220 A DCRMO-H3, RMO-H23 models – up to 300 A DC.Unlike many other handheld micro-ohmmeters available on the market, our instruments have regulated and user-selectable test currents. Therefore, RMO-H instruments generate an automatically regulated test ramp with stable and ripple-free current during measurement. These revolutionary characteristics in a handheld micro-ohmmeters technology are possible by using sophisticated Li-Po batteries. Consequently, modern battery technology enables you to do multiple measurements, and a full day of testing without recharging the battery.With all RMO-H models, it is possible to make tests on Both Sides Grounded testing objects, in an increased safety environment. Finally, these features in combination with a user-friendly interface (1-click to measure) significantly speed-up testing procedure and make it safer.These instruments store up to 1000 measurements on the internal micro SD card.Our free DV Win software communicates with the RMO-H micro-ohmmeters via a wireless Bluetooth interface. Furthermore, it allows you to download test results, analysis and generate fully configurable test reports.
