-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Interference Modeling And Simulation
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
product
Interference Locating System
SeeWave®
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
-
product
Spectrum Monitoring and Interference Systems
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
product
Canceler Series
Referenceless Canceler
The ICE2004 is an 8-channel RF Interference canceler system that achieves 40 dB of attenuation without the need for cumbersome reference signals from local transmitters. It is a simple two-port RF assembly that covers the 30 to 512 MHz frequency range. The ICE2004 unit is placed directly between the receiver and its antenna. The ICE2004 enables the reception of low-level RF signals in the presence of up to 8 strong interferers as a result of its inherent low loss path for all non-canceled signals.
-
product
Miller 400D
44550
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
product
HDMI Interface Module
HDMI modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the HDMI link untouched.
-
product
RF Hybrids
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
product
Electromagnetic Simulation Software Suite
EMTOOLS
EMTOOLS is a computational electromagnetic (CEM) software suite comprised of 16 different software codes. ACAL (Advanced Complex Algebra Library) is an out-of-core linear system solution library, using a hyper-matrix approach to partition the problem. The AntFarm™ (Antenna Farm) toolkit analyzes the radiation and electromagnetic interference (EMI) effects of single or multiple heterogeneous RF systems. Apatch™ software is an antenna design and analysis tool that provides antenna simulation and modeling by computing the radiation and receiving pattern of an antenna or antenna array installed in an operational environment...
-
product
Optical Signal Transmission
Analog
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
product
Tunable Diode Laser
Tunable diode laser absorption spectroscopy (TDLAS) is a fast, accurate, non-contact gas analysis technique that responds quickly to changing analyte concentrations. It is a proven technology free of interferences from other sample stream components.
-
product
Predictive Emission Monitoring Systems
PEMS
Predictive Emission Monitoring Systems are software-based solutions able to deliver reliable real-time emission estimations exploiting advanced mathematical or statistical models. PEMS provide accurate emission monitoring, drastically reducing the capital investment and ongoing operating costs due to maintenance activities and spare parts, minimizing the interferences with plant operations. PEMS allows plant owners and operators a better control on costs, neglecting unexpected costs due to unpredicted issues in the conventional hardware analyzers.
-
product
Pre-compliance Testing
SILENT offers pre-compliance testing for products with planned distribution to commercial and industrial markets in the US and overseas. This includes testing to ensure that emissions, immunity, and circuit-to-circuit interference problems are discovered early and immediately brought under control. We use the most advanced EMC and RF test & measurement equipment and diagnostic software available from leading suppliers.
-
product
USB 3.0 Interface Module
SuperSpeed "USB 3.0 modules" for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 3.0 link untouched.
-
product
USB 3.1 Interface Module
Super speed “USB 3.1 type C modules” for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for USB 3.1 link untouched.
-
product
H.V. Multifuntion Phasing Sticks
PC7k, PC11k, PC22k, PC33k, PC44k
Standard Electric Works Co., Ltd
● No user’s assembled parts.● Dual color-coded scale (%, Vac).● Neon indicator when >1200Vac.● Lightweight, robust & compact.● Carry case included.● Compare between phases.● Measure and test phase to earth.● High quality fiberglass wound rod.● Self powered operation. No battery required.● DC version available.● Measure phase to phase.● Hi immunity to interference fields.● Suitable for indoor and outdoor use.● Current is limited to ±1 milli-ampere.● Grounded or ungrounded systems.● Meets IEC 61481 (excludes PC44K).
-
product
Modulation Distortion Up To 53 GHz
S95070B
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
product
With SAT-IF input EDFA
HA4600/IF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
product
RF Near Field Probe Set DC to 9GHz
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
product
Smart Load Manager
Nippen Electrical Instruments Co.
This is flush mounting micro controller based instrument with multilayer PCB having SMT components offering accuracy and reliability along with reduction in EMI and EMC interference. These are specially designed to simultaneously measure, display and communicate several electrical parameters. This meter is an Ideal data source for effective Energy management, SCADA, PLC, BMS etc to measure as many as 36 parameters on 23 display pages, which are true RMS. The readings are displayed on 3 line bright Red 7 segment LED, each row/ line having 4 14.2mm high LEDS.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
Heat Flux Sensors
MF Series
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
-
product
Material Compatibility Test System (MCTS)
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
product
Site Surveys
Radiometrics Midwest Corporation
Radiometrics personnel will come to you and perform site surveys to help in the mitigation of interference or to determine if the environment contains any sources that may interfere with an individuals implanted device such as pacemakers, defibrillators, nerve stimulators, etc.
-
product
Color Assessment Cabinets
Shenzhen ThreeNH Technology Co., Ltd.
3NH's color-matching cabinet features a seamless structure design. It is 100% light-tight, preventing interference between light sources. The light sources can switch automatically, and it has a metamerism-detecting function. No pre-heating is required, and there is no flickering, ensuring fast and reliable color evaluation.
-
product
Data Acquisition & Signal Conditioners
Electro Standards Laboratories
Electro Standards Laboratories offers instrumentation and signal processors in both encased form factors or board-only versions suitable for embedded sensor applications. Features ability to collocate with sensor and provide immediate digitization and signal processing in order to minimize ambient interference on sensitive sensors and to seamlessly integrate into networked sensor architectures.
-
product
Optical Channel Monitor
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
product
Miniature Fiber Optic Pressure Transducers
*The diameter of the working length section can be as small as 0.5 French *The sensor tip size can be as small as 0.8 French The flexibility of the glass fiber offers excellent deliverability without being prone to kinking like electrical wires *The front looking configuration of the sensor tip prevent side-facing/wall bouncing artifacts in the measurement*The lack of metallic components provide full immunity to interference from RF, MW and MRI systems
-
product
Wi-Fi Performance Validation
Excentis offers a unique testing service in a real home a realistic, static, residential environment with controllable interference. This setting enables the customer to statistically compare Wi-Fi access points, as the performance is measured by a robot from different physical locations in the home, with different client types (laptops, tablets, smartphones,...) and with different operating parameters. This program can also be used for benchmarking.
