-
Product
RS232 / RS485 / RS422 / Ethernet Surge Protectors
-
Our passive, rugged, industrial-grade RS232 / RS485 / RS422 / Ethernet surge protectors are designed for direct industrial DIN-rail mounting and they come with two (2) or three (3) stages of surge protection — Gas Discharge Tube (GDT), protection resistors, and Transient Voltage Suppressor (TVS) - for maximum protection. From 2-wire RS485, 4-wire RS422 / RS485, to 10 / 100 / 1000M Ethernet, CommFront's surge protectors safeguard your data lines and provide you with a peace of mind.
-
Product
12V based Power supply for PC104 and PC104p stacks
PC104pPWR12
-
The PC104pPWR12 power supply provides for the +5, +3.3, +12, minus 12 and minus 5 from a 12V wall mount transformer supply, battery etc. Each rail is fuse protected. The supply uses switching technology to provide high efficiency coupled with low pass filtering to provide low noise and fast response to transient loads
-
Product
IC Side Channel Analysis
-
These probes allow you to couple fast, transient magnetic field, E-field, and current pulses into ICs.
-
Product
Steering Diodes
-
ProTek's low capacitance Steering Diode Arrays provide high-speed data line and I/O port protection from transients caused by Electrostatic Discharge (ESD), Electrical Fast Transients (EFT), Tertiary Lightning and other induced voltages. Steering diodes divert the transient to the power-bus or ground and away from sensitive IC components.
-
Product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
-
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
782975-01
-
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
-
Product
MTM-PM-1: 1-Channel DC Power Module
-
EXCELS AT POWER: The MTM-PM11 1: Channel DC Power Module excels at powering devices that need stable power under large transient loads during manufacturing and R&D testing. Optimized for devices using LiPo or similar batteries. Accurate voltage, temperature and current measurements can be made through the powerful and cross-platform BrainStem API.
-
Product
High Performance High Power DC Electronic Load
IT8900 Series
-
IT8900 series of high performance high power dc electronic loads provide three voltage ranges 150V/600V/1200V. The power expands to 600kW by master-slave paralleling, and maintains stand-alone functions. 50kHz high speed measurement, six working modes, transient over-power loading capability, CV loop speed adjustment, Measurement function, 25kHz dynamic test and other multiple accurate testing functions make IT8900 series well-suited for types of high power applications.
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
Engine Emission Test System
-
By adding transient operation functions (self-learning/predictive driving + each test mode performing) to measurement•control panel, Ono Sokki can build up engine test system that can perform transient mode tests supporting worldwide gas emission controls including TRIAS, FTP, EURO, and ISO. (e.g. WHDC, NRTC).This system provides good reproducibility for Transient mode test. Delay compensation and rotation inertia compensation function have greatly improved as well as self-learning / predictive driving function.Automatically processes from measurement to data output of test result, in conjunction with gas emission analyzer, tunnels, gas emission particle measurement system, smoke meter, etc.
-
Product
AC Power Sources
8500 Series
-
The EEC 8500 Series is the most power dense and functionality rich power source in our history, giving you improved capability, functionality, and a reduced footprint all in one series. This series is manufactured or simulating common grid faults, voltage dips, and other power abnormalities. The 8500 Series provides an output voltage up to 310VAC and an output frequency ranging from 5 Hz – 1,200 Hz making it the obvious solution for all kinds of applications. Not to mention, an enhanced interface to all models completely designed with the end-user in mind. Our 8500 Sources can be configured as a simple AC Power Source in MANUAL mode, as an upgraded option with Standard mode or incorporating all functions with Advanced Mode. Advanced mode adds the benefits of a sweep of voltage, frequencies, transients, and DC bias over the course of a single sequence or several different tests. The 8500 Series includes the following models: 8505, 8512, 8520, 8530, 8540, & 8560.
-
Product
HandyScope HS5 + SureConnect: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XMS-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Advanced Handheld Partial Discharge Detector
PDetector
-
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using multiple on-screen data spectrum analysis.
-
Product
C-Band DWDM Fixed Gain EDFA (FGA-C)
HWA4400 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4400 series is a fixed gain EDFA which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
Product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
-
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
Product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
-
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
Product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
-
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Transmitter (Export Only)
SMDB
-
The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
-
Product
PoE Transient Test Meter
Trans-Guard 910016
-
GrayStone Automation's innovative DCVBD voltage breakdown meter measures the breakdown voltage of many lightning protection devices and components to identify transient protection devices that may be damaged or defective and help prevent costly transient damage to critical and expensive equipment.
-
Product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785996-01
-
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Voltage Controlled Linearized Attenuators To 16 GHz
-
Pulsar's voltage controlled, PIN diode linearized attenuators are available from 0.25-16 GHz with attenuation ranges of 32 and 64 dB. Each model includes an integrated linearizer, and a driver that controls the attenuation level. This design results in transient free switching between attenuation levels as opposed to the spurious outputs that result when an attenuation value is switched either on or off by a direct digitally controlled attenuator. Transfer function is 8 dB / Volt.
-
Product
15W to 960W - Single Output
DPP Series
-
*Low Cost*UL 508 Listed*Convection Cooled*Conducted and Radiated EMI, Class B*Input Transient Protection, IEC61000-4*Conforms to EN61000-3-2 (PFC)*Three year warranty
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
-
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
Event Detectors
STD Series
-
The STD Series Event Detectors offer test specifications associated with solder joint reliability testing but can also be used for testing other types of interconnects accordingly. Like other Event Detectors, the STD series provides continuous transient resistance detection referenced to a selected threshold resistance with a high degree of electrical noise immunity.
-
Product
SIRIUS XHS
-
SIRIUS XHS - High-speed Data Acquisition SystemSIRIUS XHS is a high-speed data acquisition system (15 MS/s) with the new Hybrid ADC technology capable of high-bandwidth transient recording and very high-dynamic, alias-free data acquisition. Modern data interfaces such as USB 3.0, GLAN, XCP, CAN, and OPC UA, with PTP synchronization allow for open and flexible connectivity.
-
Product
Display Measurement Systems
DTS Series
-
Instrument Systems Optische Messtechnik GmbH
Characterization of emissive, transmissive, reflective, and transflective displaysViewing-angle-dependent analysis of illuminance, contrast, color, and derived parametersDetermination of the electro-optical transfer function: analysis of luminance, contrast, and color depending on electrical driving conditionsMeasurement of transient properties, such as switching times, flicker, and modulation
-
Product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
Product
Transient Over-voltages Tester
SUG335
-
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
Product
PXIe-4139 , ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit
782856-03
-
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 40 W of DC power. This module features analog-to-digital converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
PXIe-6378, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781476-01
-
PXIe, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6378 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6378 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
