DC/DC Converters
Takes DC input and then provides regulated and/or isolated DC output.
-
-
product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
product
PXI Digital to Analog Converters
Keysight's PXI digital to analog converters and V/I sources are capable of supplying high and low voltages levels as well as source currents on one or multiple channels.
-
product
Modbus to DeviceNet Converter
D485
The D485 Modbus to DeviceNet Converter acts as a gateway between a Modbus RTU network and a DeviceNet network. Integration of Modbus devices into DeviceNet networks is enabled without loss of functionality, control, and reliability, both when retrofitting to existing equipment as well as when setting up new installations.
-
product
AC-DC Converters
With robust, advanced high-voltage converters, power factor correctors, a variety of controllers and supervisors/housekeeping ICs, together with innovative architectures and extended temperature ranges.
-
product
Miniature Airborne Communications Converter
MACC II - Converter
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
product
Integrating Display Output A/D Converters
Renesas offers a selection of high-performance integrated display output analog-to-digital (A/D) converters.
-
product
D/A Converters
Renesas' high-speed, low-power, digital-to-analog data converters (DAC) are ideal for communication systems, medical/test instrumentation and equipment, and video applications.
-
product
Dynatrol® Digital Viscosity Converters
Series 3000
Dynatrol® Series 3000 Digital Viscosity Converters were designed for use with all Dynatrol® Viscosity Systems. Using microcontroller technology, the digital converter accepts information from a Dynatrol® Viscosity Probe and calculates the viscosity of the liquid under test. The Series 3000 converter mathematically computes and displays the viscosity in standard units.
-
-
product
HDMI Converter
B-SDI-HDMI
QuestTel''s 3G/HD/SD-SDI to HDMI mini Converter adopts Video Through Technology, delivering clear and vivid pictures on your HDMI displays. Supports auto resolution detection of 3G-SDI, HD-SDI and SD-SDI. Embedded SDI/HD-SDI audio is supported in the HDMI output allowing a convenient single cable audio/video connection. Supports resolutions up to 1080p.
-
product
Fibre Optic Converters
In complex testing environments it is often needed that electrical signals have to be transmitted into the chamber or out of the chamber to the test equipment.For that purpose we offer a variety of different interfaces that convert electrical signals into optical signals and back. Such the signal can be transported via fibre optics and is immune against electrical fields.
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
-
product
Time Code Converters
Time Codes are like different languages. All too often communication between various equipment/devices is impossible due to a "language barrier." When you encounter this type of "language barrier," a Time Code Converter can offer a very simple and cost-effective solution by "translating" a time code. ESE provides several Time Code Converters and Time Code Displays with the ability to convert one time code to another. Time Code to NTP Converter units are the most recent addition to this product family.
-
product
Digital to Resolver (AC Sine / Cosine) Converters
HDRCK
Computer Conversions Corporation
The HDRCK Series are very high accuracy, hybrid sized, high power Digital to Resolver (AC Sine / Cosine) Converters designed for industrial and COTS Military related high performance: motion control, data transmission, simulation and radar type applications.
-
product
LVDT to Digital-RVDT to Digital Converters
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
-
product
O/E Converter
TIA-3000
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
Isolated D/A Converter 8 Channel, 250kSa/s
OTP2 module no.187
The PXIe‑4322 is a channel-isolated analog output module with built-in signal conditioning. The module provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters in one device, the PXIe‑4322 isolated analog output module offers smaller dimensions and higher measurement performance. In current mode, the module operates in all four quadrants, allowing current to be drawn and sourced. Thanks to isolation and outputs for higher voltages and currents, the module is particularly suitable for applications in the automotive sector.
-
product
Frequency Converter Test Solution Up To 50 GHz
N5245BP
The N5245BP provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter test up to 50 GHz. This bundle product
-
product
PWM to Voltage Output D/A Converters
Analog Devices’ pulse-width modulation (PWM) to voltage output D/A converters convert a PWM input to an accurate, stable, buffered voltage without the ripple, slow settling, and external passive components of discrete filter implementations. Our PWM D/A converters measure the period and pulse width of a PWM input signal and immediately update the D/A converter output with up to 12-bit accuracy and no software coding required. This family of D/A converters is available with 8-bit to 12-bit resolution, dual and quad channels, integrated references, and with high temperature operation. Applications include isolated motor control, automotive headlights or industrial lighting, and other applications that benefit from the simple control interface.
-
product
Wall Transformer, Converters & Chargers
PeakTech Prüf- und Messtechnik GmbH
An appliance for holding or inserting a charge of power.
-
product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
product
Unidirectional Single-Phase & Three-Phase Analog Converters
We produce and market AC/DC analog converters to control DC motors. The 3DBS series is under START POWER design and implementation. This product can be used either as motor control or power supply, indifferently, and is available in the standard series from 40A to 500A.
-
product
Airborne Frequency Converter
AFC Series
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
product
DCDC
TA Series 25 Watt
The 25-Watt TA series operates over an ultra wide input range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 77% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.5” x 3.0” x 0.83”
-
product
AC DC Current and Voltage Converters
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
product
Catalytic Converter Measurement
OMCAT
OMCAT catalytic converter measuring systems provide a fast and efficient means of carrying out complex geometrical measurements on exhaust catalytic converters and of determining the gap bulk density (GBD). OMCAT measuring systems feature innovative measurement functions combined with reliable technology. High measurement speed and accuracy and high availability due to their rugged construction are the major strengths of these systems which come to the fore in the harsh conditions which prevail in production environments.
