DC/DC Converters
Takes DC input and then provides regulated and/or isolated DC output.
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
Antenna Impedance Converter
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
product
DC/DC Power Supply
ISM-DC-AT512-P
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
product
CAN + OBD Network Data Converter
NC1
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
product
SCSI Converters
Paralan's wide product line of SCSI Converters permits different SCSI Bus types to communicate with ease and reliability, and with no loss of data throughput.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
Signal Isolators & Converters
Devar current loop signal isolators reduce problems found in field measurements when signal transmitters or converters encounter both input and output signals that may be grounded. Current loop isolators eliminate these ground loops and are available as input loop powered or output loop powered instrumentation.
-
product
Ethernet To Fiber Optic Converters (Multi-Drop)
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
product
Multiplying Current Output D/A Converters
Analog Devices offers a wide range of high precision, multiplying current output (IOUT) D/A converters (DACs) that feature ±1 LSB INL and DNL specifications, from 12-bit up to an industry-leading 18-bit resolution. Our portfolio includes single and multiple D/A converters in small packages with parallel or serial SPI interfaces. Multiplying current output R-2R D/A converters allow for an external amplifier that’s optimized for specific applications and that does not require reference buffering, which enables high linearity. The SoftSpan™ feature allows software selectable output spans, therefore eliminating the need to add precision gain stages and the associated external jumpers, precision resistors, and amplifier circuitry. Integrated precision resistors allow for reference inversion, bipolar offset, and offset and gain adjustment.
-
product
Multichannel Voltage Output D/A Converters
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
-
product
Signal Converters & Load Cell Signal Converter
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
product
Up Converters
Macom Technology Solutions Holdings Inc.
MACOM's upconverters are widely used in point-to-point radio, broadband communications, and RADAR applications. Operating up to a frequency of 86 GHz, our upconverters feature an integrated image reject (balanced) mixer, LO buffer, and RF buffer. Some products also include LO multiplication and variable gain, all within a single chip. Available in die, or SMT lead-free QFN and LGA packages, our upconverters boast excellent performance with adjustable bias, high linearity and image rejection with low LO leakage
-
product
RF Mixers & Frequency Converters Overview
Up and down conversion is often used because waveform generation in a transmitter is less expensive at lower frequencies and the dynamic range of analogue-to-digital converters in the receiver is higher at lower frequency.
-
product
LVDT to Digital and RVDT to Digital Converters
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
-
product
Lamp Converters
PeakTech Prüf- und Messtechnik GmbH
This AC / AC voltage converter is particularly suitable for use with halogen indoor lights and other low-voltage light sources that require an AC voltage source for supply. There is a safe galvanic separation between mains and low voltage according to the isolating transformer standard. This pre-assembled AC / AC converter is equipped with an overtemperature switch that cannot be reset.
-
product
Dynatrol® Digital Density Converters
Series 2000
For increased speed and accuracy, use the Series 2000 Digital Converters with all Dynatrol® Density Cells. Microcontroller technology measures to meet your needs: Density, Specific Gravity, °Brix, Baumé, API Gravity, Percent Solids, Percent Concentration, °Twaddle of liquids and slurries.
-
product
In-line ICP® Charge Converters
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
product
Interface Converter
ZET 7174
*Interface converter USB↔CAN 2.0*Digital sensors and controllers power supply*Data exchange with PC
-
product
Frequency Down Converters
In digital signal processing, a digital down-converter (DDC) converts a digitized, band-limited signal to a lower frequency signal at a lower sampling rate in order to simplify the subsequent radio stages.
-
product
mAEStro Audio Digital to Analog Converter
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
product
Digital to Synchro Converter
DSPH
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
product
ARINC 818 to HDMI Converter
The ARINC 818 to HDMI converter is a rugged standalone module available in half-length PCIe form factor used for ARINC 818 to HDMI conversion, HDMI to ARINC 818 conversion, 2x ARINC 818 Switch as well as ARINC 818 Duplicator/Splitter. It is a video Converter module designed with Kintex-7 FPGA, using an Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
product
Scalar Mixer / Converter Measurements
S97082B
The S97082B scalar mixer/converter measurements enables the highest accuracy for scalar conversion–loss/gain measurements with a simple setup and calibration
-
product
High-Speed F/V Converter
FV-1500
FV-1500 High-speed F/V Converter is a frequency-to-voltage (current) converter that converts frequency signal proportional to rotation speed, moving speed, etc. into voltage signal.The FV-1500 is designed to accommodate the needs of high speed rotation measurement including rotating motors used in HV/EHV production lines etc. It also contributes to measure rising characteristics, very small fluctuation in steady rotation, and transient phenomena of flow speed with fast response.
-
product
WIFI Converter
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
product
Interface Converter
ZET 7076
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
