Conductivity
-
Product
Universal Cable/Harness Tester
LX-680
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The maximum test spot is 256.
-
Product
HIL and RCP DFIG Laboratory
-
This laboratory combines the best of both OPAL-RT and Festo solutions to deliver academic researchers and teachers with the ideal Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) simulation system to conduct experiments and teach in the fields of electrical machinery, power converters and wind energy generation.
-
Product
Levitator
-
The ultrasonic levitator is ideally suited for a large number of material science experiments in which small samples or sample quantities have to be positioned precisely. Measurements can be conducted – as they are performed in a touchless manner – without interference from a contact surface.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
IEC60884-1 Plug Socket Switch Life Tester With 3 Stations
CZKS-4
-
Shenzhen Chuangxin Instruments Co., Ltd.
1. This test equipment is designed and manufactured according relevant requirement of Standard IEC60884-1,GB2099.1 and GB16915.1,Mainly used to test the service life of household and similar use plugs and sockets or switches. 2. This machine connect to load cabinet and conduct electrical life test ,normal operation and breaking capacity to plug socket and switch.
-
Product
CTDs: Profiling
-
Profiling CTDs make continuous measurements as they travel through water. When lowered over the side of a ship or integrated with an autonomous vehicle, they map a vertical column of water's characteristics. Compared to moored CTDs, profiling CTDs account for dynamic errors introduced by moving through water and sample rapidly to generate a high-resolution dataset over a short period of time. Sea-Bird Scientific profiling CTDs are:*Designed to perform under unique dynamic conditions found on moving platforms.*Pumped and ducted for constant flow to match temperature and conductivity response.*Plumbed so measurements are made on the same sample of water with a predictable delay and predictable flow effects.*Built with a rugged design for shipboard and autonomous deployments.
-
Product
500 Watt AC/DC Power Line Conditioner, 3U VPX, Holdup Time
VPX56-3HU
Power Line Conditioner
NAI's VPX56-3HU is a rugged, high-performance 500-Watt Output +28 VDC Input 3U VPX AC/DC Power Line Conditioner designed for aerospace, defense, and industrial markets. This off-the-shelf power supply plugs directly into a standard VPX conduction cooled chassis and protects downstream DC-DC converters from MIL-STD-704 transients, low-voltage conditions and power interruptions, providing up to 50 milliseconds of holdup time at up to 500-Watts. Continuous Background Built-In-Test (BIT) and I2C communication are included.
-
Product
DCDC
GA Series
-
The GA series is an economically priced 15 watt DC/DC converter featuring ultra-wide input range, efficiencies to 85% and a continuous six-sided shielded case. Low ESRcapacitors are used both on the input and the output(s) to minimize the conductive noise. Other key features include: overvoltage protection, output trim adjustability, TTL and CMOS compatible remote on/off, short circuit protection and small size. The GA series measures only 1.6” x 2.0” x 0.40” and offers a power density of 11.7 watts/cu. in.
-
Product
6U VPX PCIe to XMC Expansion Board
VP69601
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP69601 is a 6U VPX PCIe to XMC expansion board. Onboard there is a x8 PCIe 3.0 interface, and through a PCIe connector the x8 PCIe 3.0 turns into 2 x8 PCIe 3.0 linking to 2 XMC cards. The PCIe Switch IC on VP69601 supports DMA, so direct data transmission between peripheral cards can be realized.VP69601 can be installed in a standard VPX chassis and work as a peripheral board. VP69601 carries two XMC ports, through which users can expand various functional XMC cards needed.Apart from the traditional Air Cooling design, Linkedhope○R provides a Conduction Cooling version to guarantee working stability of VP69601 in extreme and vibration environment and in an extended working temperature from -40℃ to +70℃.
-
Product
Online Analyzers
-
Analysers which are connected to a process, and conduct automatic sampling.
-
Product
Industrial Panel Controls
-
Panels controls are designed for applications that typically require frequent adjustment. Both rotary and slide panel control types are available. A selection of elements includes carbon, cermet, and conductive plastic. These devices are available in various sizes and shaft/bushing combinations. Some models are available with a rotary switch and seal options. Typical applications include audio mixing consoles, test and measurement equipment, consumer electronics, and medical equipment.
-
Product
Subsea Pipe Detection & Tracking System
HydroPACT 440
-
The HydroPACT 440 pipe detection system has been established for a number of years as the industry standard, providing accurate and reliable survey data, which provides the position of conductive assets on or beneath the seabed. The system is flexible in its range of uses and can be installed on a variety of vehicles for undertaking survey work.It provides a reliable and simple method for performing accurate submarine surveys on a conductive target such as a cable or pipe.
-
Product
EMC Subracks
101.1/10/11
-
VECTOR Electronics and Technology, Inc.
VectorPak™ EMC Rugged subracks for heavy duty applications where a high resistance to shock and vibration is required. Its features include heavy two-screw fixing extrusions, 2.5mm thick side panels / rack flanges and conductive finish throughout.
-
Product
Porometer/ Fluorometer
LI-600
-
The LI-600 is the only handheld instrument that measures both stomatal conductance and chlorophyll fluorescence over the same leaf area.
-
Product
Qualification Testing
-
Teledyne Storm Microwave ensures your design specifications are met by conducting in-house testing at all production phases. This comprehensive qualification process guarantees high-quality performance and reliability in every cable assembly, meeting the stringent requirements of your application.
-
Product
Conductive Footwear Tester
SLTM-1
-
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
Product
PH and Conductivity Meters
-
PeakTech Prüf- und Messtechnik GmbH
It is possible to measure the conductivity of liquids, for example of water. The purer the water, the lower the conductivity (for example, distilled water is purer than normal water and has a low conductivity of approx. <10 µS).
-
Product
Conductivity Meters
-
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
Product
Electrical Machine Trainer
-
We are counted amongst the renowned names in the industry, offering wide range of Electrical Machine Trainer It is so much easy to conduct and understand and are offered in standard configurations. They are reliable in nature and have high strength. Electrical Machine Trainer is performance based and is used in industrial and commercial sectors.
-
Product
Portable Thermal Conductivity Meter
TLS-100
-
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
Product
PRO Conductivity (EC) Monitor
MC310
-
The Milwaukee MC310 PRO Conductivity (EC) monitor lets you measure EC levels automatically and alerts with an alarm when out of the set point range.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Conductivity Type (P/N) Checker By Contact Thermo-electromotive Force Method (seebek Effect)
PN-12α
-
*Thermo electrode and cold electrode is mounted detecting part of measuring probes*Possible to check most figure of sample such as single crystalline silicon wafer, bulk, ingot and so on*Please select from 2 types;1) 2 probe ver.(Hot probe, Cold probe),2) 1 probe ver.(Hot & Cold probe)
-
Product
Glow Wire Tester
TF346
-
TESTEX Testing Equipment Systems Ltd.
Glow Wire Tester, to determine the resistance to fire insulating parts. The testing of electro-technical products for fire hazard is conducted by simulating as closely as possible actual effects occurring in practice. Parts of electro-technical equipment which may be exposed to thermal stress due to electric effects & deterioration of which may impair safety of equipment shall not be unduly affected by heat & fire generated within the equipment.
-
Product
Scienlab Energy Storage Discover Software
SL1091A
-
The Scienlab Energy Storage Discover (ESD) is a central component of all Scienlab energy storage test environments.The intuitive software allows users to conduct tests that deliver concrete, stable, and reproducible results.
-
Product
Coupling Decoupling Network
TBCDN-M1
-
The TBCDN-M1 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Scanning Electron Microscopy (SEM Analysis)
-
Rocky Mountain Laboratories, Inc.
Scanning Electron Microscopy (SEM Analysis) can produce images of almost any sample at magnifications of 15-300,000X. The SEM has tremendous depth of field allowing for imaging that cannot be accomplished using optical microscopy. Conductive and nonconductive samples can be imaged. When operated in the backscatter (BSE) detection mode, differences in material composition can be observed. Elemental analysis can be performed on any feature observed with an integrated Energy Dispersive Spectroscopy (EDS) detector.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
General Purpose Heat Flow Meters
-
Thermal conductivity defines a material’s ability to transfer heat. A precise and accurate measurement is critical for any process or material experiencing large or fast temperature gradients, or for which the tolerance for temperature changes is exacting. Accurate values are essential for modeling and managing heat, whether the component of interest is called on to insulate, conduct, or simply withstand temperature changes. Information about these properties are routinely used in heat transfer models of all complexities. Thermophysical property measurements also reflect important information about material composition, purity and structure, as well as secondary performance characteristics such as tolerance to thermal shock.
-
Product
Guided Wave Radar Level Transmitter
2291
-
The 2291 Guided Wave Radar level transmitter is designed for continuous level measuring of conductive or non-conductive liquids, pulps and solids. The 2291 level gauge operates based on the well-known TDR (Time Domain Reflectometry) principle. Micropulses are sent along a probe guide at the speed of light. As soon as the impulse reaches the surface of the medium, it is reflected back to the electronic module. Level distance is directly proportional to the flight time of the impulse.
