Test Probes
See Also: Probes, Microprobes, Probe Cards, RF Probes, Test Fixtures, Test Heads
-
Product
SMT & THRU HOLELOADED BOARD TEST PROBES
SERIES 43
-
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
Eddy-Current Sensors
-
Eddy-Current sensors are noncontact devices capable of high-resolution measurement of the position and/or change of position of any conductive target. Eddy-Current sensors are also called inductive sensors, but generally "eddy current" refers to precision displacement instruments (or nondestructive testing probes) and "inductive" refers to inexpensive proximity switches. High resolution and tolerance of dirty environments make eddy-current sensors indispensable in today's modern industrial operations.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
General Purpose Test Probes
-
Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle
-
Product
PCIe Carrier For PMC And PrPMC
PCI104
-
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
Product
Single Function Installation Testers
-
A handheld insulation resistance and continuity tester. Its unique integrated safety probe puts the LCD and test probe in the user's line of sight whilst making measurements.
-
Product
Test Fingers & Probes
-
Test Fingers and Probes are used in most standards to check accessibility to moving parts or hazardous live parts. They comes in many forms, such as test fingers, test rods, test balls etc.
-
Product
Stand-Alone Test Fixture
MA 2013/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
Product
Probe Cards
Direct Dock
-
Direct dock style wafer probing allows for a higher bandwidth, increased pin density and testing more devices in parallel. Direct dock probe cards also support the growing movement of traditional final test to wafer probe which allows for known good die (KGD) and reduced cost of ownership.
-
-
Product
Digital Engine Analyzer/Multimeter
385A
-
The #385A has many of the necessary features required for today’s automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Extended Test Lead Kit
U1161A
Accessory Kit
The Keysight U1161A extended test lead kits are compatible with the U1230, U1240, U1250, and U1270 Series handheld digital multimeters. The set includes two extension test leads (one red and one black), two test probes, medium-sized alligator clips, and 4 mm banana plugs.
-
Product
Test Finger Probe
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s test fingers, test probes and test needles comply with IEC 60065, IEC 60238, IEC 60335, IEC 60529 and IEC 61032 standards and are essential instruments for the protection against electric shock of household and similar electrical appliances. For more information, please contact us and BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Passive probe with X1/X10 switch
-
They are normally designated X1 and X10, although 1X and 10X are sometimes seen. The designation refers to the factor by which the impedance of the scope itelf is multiplied by the probe.The X1 probes are suitable for many low frequency applications. They offer the same input impedance of the oscilloscope which is normally 1 MΩ. However for applications where better accuracy is needed and as frequencies start to rise, other test probes are needed.
-
Product
Automated Bare Board Tester with Built-In Camera
QTOUCH2404C
-
Qmax Test Technologies Pvt. Ltd.
Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.
-
Product
Battery and Alternator Analyser for 12V DC Systems
1176
-
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Product
CAMGATE Test Kits
Series 453
-
LThe GR Series 453 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 453 provides interface compatibility using the GR2270 Style, 12 block interface. This interface accepts the industry standard I/O, power, and coax blocks. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
Product
THRU HOLEBARE AND LOADED BOARD TEST PROBES
SERIES 93
-
ElectricalMAXIMUM CURRENT: 7 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS mean
-
Product
The Mag Lead
136
-
*Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
-
Product
30 AMP Fuse Buddy Testers
FB305M
-
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
Product
MANIA TEST PROBE
SERIES 76
-
ElectricalMAXIMUM CURRENT: 3 amps continuousat working travel, non - inductiveRESISTANCE: At 35 mA test current,50 mOHMS meanMaterial and FinishesPLUNGER: Heat treated berylliumcopper, FINISH: -2E / -2P Hard nickel plated-2D / -2E138 24 Kt gold plated,BARREL: Phosphor bronze, nickel platedSPRING: Stainless steel, silver platedPIN: Music wire, hard nickel plated
-
Product
Test Probe
-
INGUN, which has earned tremendous trust and achievements from customers all over the world in terms of quality and durability , has a network of distributors in about 50 countries around the world, and has a product lineup of more than 20,000 types.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Terminal Test Kit (92 Pcs)
3601C
-
Peaceful Thriving Enterprise Co Ltd
*Total: 92 pcs*Alligator clip x 2 pcs*Testing probe x 2 pcs*Flat terminal x 48 pcs*Testing needle x 4 pcs*1 to 2 connector x 2 pcs*Round terminal x 24 pcs*5K variable resistor x 2 pcs*Polarity tester/stroboscope x 2 pcs*SRS air bag replacement connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs
-
Product
Probe Card Analyzers
PB3600
-
The PB3600 provides the latest techniques in testing and maintaining probe cards. Designed through joint development with many of the world’s largest semiconductor and probe card manufacturers, ITC has produced an ergonomic analyzer with the greatest measurement resolution, highest throughput, most flexibility and still made it easy to use.
