Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
PFC Controllers
-
Renesas' power factor correction (PFC) controller family uses boost topology and are suitable for AC/DC power systems, up to 2kW and over the universal line input. These PFC controller IC's operate in continuous conduction mode (CCM), and the small external components result in a low cost design without sacrificing performance.
-
Product
Analog Signal Generator
ASG
-
The pocket size model ASG Analog Signal Generator is an ideal tool for troubleshooting transmitters, transducers, motors and actuators. The unit generates a 0 to 10 VDC signal in increments of 1 volt or a 4 to 20 mA signal in increments of 2 mA. An LED bar graph visually indicates analog signal level. The model ASG will also continuously ramp to user defined maximum and minimum values with user defined ramp interval timing. Units are furnished with 6 ft (1.8 m) leads with alligator clips, 120 VAC plug-in adapter, protective carrying case and instruction manual.
-
Product
Conformance Test Systems
-
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
Product
Power Contacts
-
VPC’s Power Contacts are a family of high‑current, long‑life contacts for Mass InterConnect and cable/PCB interfaces, covering roughly 21 A to 500+ A continuous (up to about 1500 A in low‑duty applications) at up to about 1500 VDC or peak AC
-
Product
Solar Simulator Continuous Light
-
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
Product
Highly Flexible Miniature Cable Assemblies
FlexFit
-
Does your application require:- Low resistance to flexure? - Continual movement?- Low weight?- Does it have tight space constraints?Whether you're facing one or more of these issues, FlexFit™ assemblies can provide your solution. The FlexFit™ cable has a stranded center conductor that offers ultra flexibility (>500,000 flexures) with electrical and physical stability.And, its small size (0.052"/1.32 mm OD) satisfies weight and space constraints that can impact ease of installation.
-
Product
FTIR Gas Analysers
-
Protea’s range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases.
-
Product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
Digital I/O Module
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
Primary Injection Test Set
T1000
-
T1000 primary injection test set is the model featured with light weight and 2 minutes continuous output time at 1000Aac.
-
Product
IPTV Testing
-
EXFO offers IPTV test solutions to assess the network copper physical layer, validate the xDSL service and test the performance of the IPTV component at any stage of the deployment. Our Ethernet IPTV testing, IPTV analysis capabilities and advanced IPTV monitoring solutions offer complete end-to-end quality of experience (QoE) assessment for IP video. EXFO enables providers to successfully introduce video services faster and manage them more cost-effectively, by continually ensuring the highest service quality.
-
Product
Power Supplies
EARTHWATTS
-
Get the power you need and the low electric bill you want with Antec’s EarthWatts 380D Green! Antec introduces one of the most environmentally friendly power supplies on the planet, the EA-380D Green, which delivers 380 watts of reliable, continuous power while meeting the Bronze level of performance from 80 PLUS®, the most widely recognized independent standard in power supply efficiency. Go green” with Antec’s EA-380D Green: an efficient, cost-effective power supply solution that lets you power your equipment, save money and protect the environment. No power cord included. By reusing your existing cord, you can reduce waste and help protect the environment.
-
Product
PCI Express 4.0 Protocol Analyzer Exerciser
Summit T416
Protocol Analyzer
The Summit™ T416 analyzer is the computer industry's first high speed PCIe 4.0 protocol analyzer that meets the challenge of 16GT/s and up to x16 lane width protocol analysis. Many PCIe 4.0 product designs are already in progress using the PCIe 4.0 specification. Companies are currently working with the Teledyne LeCroy Summit Z416 protocol exerciser for PCIe 4.0 at the deployment of PCIe 4.0 for host system emulation with their testing needs. This combination of a protocol analyzer and exerciser make Teledyne LeCroy the only supplier of protocol test and development tools for PCIe Gen 4. High speed interposers that provide protocol analyzer connectivity to CEM or other form factor sockets on system boards will still continue to be the principle way to capture PCIe traffic into the protocol analyzer.
-
Product
Multifunction Electrical Installations Meter
MPI-520
-
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
Product
True RMS Clamp Meter
DL489
-
UEi Test & Measurement Instruments
The DL489 True RMS Clamp meter offers contractors better features, functions and safety in a commemorative edition housing. A complete meter with the precision of True RMS and the functionality your job requires. Featuring 600A AC/DC, 750V AC and 1000V DC, resistance, capacitance, diode test, continuity, microamps and LRA Inrush. The DL489 is the complete meter your job requires.
-
Product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Power Sensor
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
Product
Subsea Pipe Tracking System
HydroPACT 660E
-
With HydroPACT 660E Teledyne Marine brings the world’s smallest submarine, pulse induction pipe tracker to market. Built upon the already established, industry standard and world leading TSS HydroPACT 440 system, the HydroPACT 660E continues the legacy by bringing pipe tracking and UXO detection capabilities to small inspection and observation class ROVs, for applications that were previously only available on larger vehicles such as work class ROVs and trenchers.The HydroPACT 660E has a single 24 Vdc, small subsea electronic pod, dramatically reducing the installed footprint and payload of the system while maintaining an operating range of greater than 85% of that of the significantly larger HydroPACT 440 system. The coil array features an integrated cable for even greater reliability and is suitable for installation and operation on smaller Observation class ROVs.
-
Product
Handheld Circuit Breaker And Timer Analyser
CAT-H Series
-
The operation of the breaker can be initiated in different ways (e.g. from a control room, by a local breaker or externally by a test device) depending on the test conditions. Various time measurement triggers are available to record a measurement under a different test condition:*Coil control channel*Continuous current clamping channel*DC voltage channel
-
Product
Gas Analysis
QIC BioStream
-
A gas analysis system for continuous analysis of gases and vapours from multiple fermentation reactors with multi off gas and multi reactor dissolved gas species analysis capability. A high-performance Proteus multi-stream valve supplied with 20, 40 or 80 inlet streams is included with programmable sequence control software for analysis of multiple reactors. Streams can be allocated for either dissolved species analysis or off gas analysis.
-
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated• Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV • Resistance range to 1TΩ • Continuous digital display on LCM• Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
Multifunction Module for 34970A/34972A
34907A
Digital I/O Module
The Keysight 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two 12V analog outputs - all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
-
Product
MPO Visual Cable Verifier Kit
KI-TK824
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end. Fiber 1 is easily identified with a winking light.
-
Product
GAMCHEK JR.™
GT3108
-
The GamChek is a quick and easy way to check your dimmer output for power, correct polarity and ground. If you have a live power outlet and will also alert you if there is a problem with polarity and if there is a correct ground path. Label on the back on the unit indicates circuit continuity.
-
Product
600A Digital Clamp Meter
7128B
-
Peaceful Thriving Enterprise Co Ltd
This is a auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity and non contact voltage sensing. Sub switch included Function Select, Max-Min Indication, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Illumination and Back-light.
-
Product
Handyscope TP450-50XM-W5
TP450-50XM-W5
-
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Product
DCDC
QQA Series
-
The QQA series features the latest in MOSFET design, state of the art surface mount technology, and offers a 4:1 ultra-wide input range, and efficiencies greater than 80% (typ). Features include continuous short circuit protection, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. All models are packaged in a six-sided shielded miniature case measuring only 1.0” x 2.0” x 0.4” high.
-
Product
Laser Source
TW3110
-
Techwin(China) Industry Co., Ltd
Laser Source TW3110 is the most rugged small size instrument in the industry. It integrates super small size and strong function in one unit. With 3 pieces of 1.5V alkaline batteries, it can work continuously for more than 40 hours. The total weight is only 110g. Together with the TW3205 Mini optical power meter, it provides an excellent solution for fiber optic network and for field work.
-
Product
Mechanical Creep and Rupture Testing Machine
MRC Series
-
Jinan Testing Equipment IE Corporation
MRC series mechanical creep and rupture testing machine with single-lever structure is designed for long-term creep and stress rupture test applications. The series mechanical creep and rupture testing system is mainly for the metallic materials under room or elevated temperature according to GB/T2039, GB/T 20120, EN ISO 204-2009 and ASTM E139. The creep and rupture testing machine can also maintain constant loads for extended periods of time. Through the mechanical advantage of the lever arm loading system, constant loads can be maintained with a high degree of accuracy for long duration. This creep and rupture tester uses dead weights without continuous operation and the dependency of a mechanically powered drive. The creep and rupture testing system is an ideal equipment for metallurgy manufacturer, research institute, colleges and other relevant factories and mines.
-
Product
Memory Analyzers
-
Market drivers in the memory sector have changed. Gone are the days of simply pushing Moore’s Law to ever faster data rates. The memory designs of today and tomorrow must also be smarter than ever before. Today, handheld and wearable computers must draw from a limited battery reserve while serving up fast, responsive, and compelling mobile experiences. Meanwhile the cloud of data centers and server farms that feed us these compelling experiences must continuously grow while simultaneously reducing overhead and environmental impact. These two different markets have the same goals: smarter memory, smarter control systems, and lower power usage.
-
Product
Eddy Current Chassis Dynamometers
-
Cradle- or single-roll (top-mount) dynamometers accommodating single- or tandem-axle vehicles, with continuous vehicle power ranges from 50 hp to 622 hp (37 kW to 464 kW), Taylor’s chassis dynamometers allow a top recommended speed of 90 mph (145 kph) at full load. Look to our experts to not only help you select your optimal system, but also to provide design, configuration, installation and training for a total solution that integrates seamlessly with your operation.
