-
product
Autocompute LCR-Q Meter Sorter
Model 4912 / 4912PR
- Microprocessor based Fully Automatic L, C, R, Q and D measurement- Autoranging with Direct Digital Readout- 4 Terminal Measurement Technique- No Tuning or Balancing- Series or Parallel Equivalent Measurement- Absolute Value and Nominal Value with Percentage Tolerance- Single / Multiple Parameters Check During Component Sorting- Feather Touch Keys with Audio Feedback- Thermal Shut Down for Overheat Protection- Special Mechanism for Fast and Easy Insertion and Removal of Test Component- Low Cost and Portable- Component Sorting on Absolute or Nominal Value Basis with a Percentage Tolerance- Aplab Model 4912PR is Remote Programmable Auto Compute LCR-Q Meter Sorter, Which can be Programmed through GPIB, RS232 or SPIB Interface
-
product
Channel Emulator
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
product
Transmitter
5081
The Model 5081 family of transmitters can be used to measure pH, ORP, conductivity (using either contacting or toroidal sensors), resistivity, oxygen (ppm and ppb level), free chlorine, total chlorine, and ozone in a variety of process liquids.
-
product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
product
Ultra-low Noise High Voltage Amplifier
WMA-200
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
product
3D-Control FAYb Laser Marker
LP-Z Series
Panasonic Industrial Devices Sales Company of America
The LP-Z Series Fiber Laser Marker features:- Compact Air-Cooled Head- Full 3D Capabilities- 13 And 25 Watt Models- Wide Marking Area Up To 330mm- Economical And Flexible
-
product
High-Speed Analog Input Processor
DAP 5380a
The DAP 5380a model, optimized for high-speed analog input, works well in simultaneous sampling applications. By grouping a number of these boards into a single synchronized system, you can simultaneously sample high-speed inputs in groups
-
product
Micromanometer
6700
The Handheld Micromanometer – Model 6700 can be used with pitot tubes, flow grids, differential pressure tubing, or the optional velocity-grid (for average face velocity readings). It comes standard with the Model 6715 TABmaster Capture Hood, but is also available for purchase separately.
-
product
Low Dew Point Hygrometer
DewTech 390
The Edgetech Instruments Model DewTech 390 is a Precision Low Dew Point Hygrometer which offers measurement of extremely low Dew Point or Trace Moisture for a variety of background gases at a very attractive price. Based on the Primary Standard Chilled Mirror measurement technique, it provides absolute knowledge of dew point and is provided with a NIST traceable calibration certificate.
-
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
product
Electronic Circular Temperature Chart Recorder
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
product
Mid-Range Gas Filter Correlation CO Analyzer
Model T300M
Teledyne Advanced Pollution Instrumentation
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.
-
product
Stack Gas Analyzer
ENDA-7000 Series
After decades of experience in precise stack gas measurement, HORIBA's brand new ENDA series represents the ultimate stack gas analyzer. With enhanced lower cost and reduced maintenance time, high sensitivity, and usability, we focused on the users' point of view. The ENDA-7000 is designed to continuously measure the concentrations of NOX, SO2, CO, CO2, O2, and NH3 in stack flue gas streams. The model is offered in dozens of combinations based on your measurement requirements. The ENDA-7000 uses an extractive method which measures undiluted sample gases, and is very suitable to stack gas measurements such as shale gas, LNG, or biogas and other combustion applications. The ENDA-7000 is an excellent choice for measurements in power generation facilities, boilers, furnaces, steel manufacturing, cement plants, pulp and paper mills, etc.
-
product
DC Power Supplies
Single, dual or triple output models with power from 30 watts up to 1200 watts. Linear, Mixed-mode or PowerFlex regulation. Remote control models with variants of Analog, USB, RS232, GPIB and LAN interfaces.
-
product
Surface Quality Monitors
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
product
Ultrasound Transducers
Utilizing optical and semiconductor fabrication techniques, Imaginant manufactures the PureView PrecisionTM line of RoHS-compliant delay-line ultrasound transducers with center frequencies ranging from 50 MHz to 250 MHz (higher and lower transducer frequencies are also available). Imaginant's precision-manufacturing process produces transducers that exhibit high reliability and high uniformity from device to device. This manufacturing consistency enables uniform test system performance to be attained across multiple systems. Imaginant transducers are available in focused and flat-face models that can be produced with minimal-damping for applications requiring maximal sensitivity or with maximal-damping and high-bandwidth for applications requiring the highest-degree of temporal precision.
-
product
Rugged Igniter Tester
4314 KV
Model 4314 KV is a 4-wire ohmmeter designed to use low test currents for its measurement. Additional circuitry proprietary to Valhalla Scientific is used to ensure that test current levels do not exceed the specified “fail-safe current” even in a worst-case component failure situation.
-
product
DC Power Supplies
DCS Series
AMETEK Programmable Power, Inc.
The DCS Series of 1 kW, 1.2 kW and 3 kW programmable power supplies provides a highly reliable power platform. It utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low profile chassis. This DCS power supply family has an easy-to-use front panel with 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and over voltage protection, status and constant-voltage/current mode operation. The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/local programming and preview status of voltage, current and OVP setpoints.
-
product
Angular Orientation Sensor
WOS-120
The Miniature Angular Orientation Sensor system Model WOS-120 contains both a 3-axis fluxgate magnetometer and a 3-axis accelerometer. These sensors are sampled by an internal A to D converter and microprocessor subsystem which outputs 16 bit digital data representing the magnetometer and accelerometer readings. The system can also be configured to transmit the roll, pitch and azimuth orientation angles of the Model WOS-120 system. These angles are calculated before transmission from the accelerometer and magnetometer sensor output data.
-
product
Differential Probe
DP-16K Series
*High Frequency Performance Model*Bandwidth:(-3 dB)**DC~100 MHz (DP-16K)**DC~70 MHz (DP-16KM)**DC~50 MHz (DP-16KL)*2 Range: x100, x1000*Input Impedance:**10 MΩ // 10 pF each side to ground*Over Range Indicate LED*Rise Time: 4 ns
-
product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
High Range Chemiluminescence Oxides of Nitrogen Analyzer
Model T200H
The Model T200H combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. A high-efficiency stainless steel thermal NO2 converter provides durable and consistent operation under the harshest conditions (other converter options also available).The T200H may be fitted with an optional, internal paramagnetic O2 sensor or an infrared absorption CO2 sensor, reducing integration and operating costs significantly. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T200H comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
High Impedance Active Probes
7
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
product
Technical Manual Probe Station
4060 150-200 mm
Micromanipulator's Tech Series Probe Station, Model 4060 is designed to provide a quality 6-inch (150mm) or 8-inch (200mm) probe station at a cost effective price
-
product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Software Quality Consulting & Cloud Strategy Consulting
For this reason we use a set of overarching principles and supporting processes to structure our consulting advice, rather than be enslaved by them. Therefore, our 5 overarching principles include: Quality and time to market are key drivers of business successMethodologies and models must be adapted to suit the customer's journey and desired stateA successful development and quality program is built on the bedrock of a high-performance cultureApplications should conform to business' needs, not vice-versaThe past should teach us lessons, not be consigned to the recycle bin
-
product
CW (Continuous Wave) Magnetrons For Industrial Microwave Heating
Insight Product offers CW magnetrons models for industrial and commercial microwave heating, the frequencies 915 MHz and 2450 MHz with output power up to 100 kW. We offer these CW Magnetrons together with accompanying solenoids, based on Permanent magnet or Electro-Magnet depending on model.
-
product
Oscilloscope, 100 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2104HD-MS
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
-
product
Filters
High performance and high quality. Mercury Systems' filter products utilize the latest in filter technology and are supported by the Mercury commitment to quality and innovation. With experience manufacturing space-quality hardware, Mercury has developed the capability for reliability to be built-in from the first design phase. With state-of-the art modeling software and an on-site machine shop, Mercury Systems is ready deliver a standard product or custom design.
