-
product
3-Ch 200 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52621
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Optional LVPECL clock/sync bus for multiboard synchronization- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Benchtop Conductivity Meter
LAQUA EC2000
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
product
Modal Exciters & Amplifiers
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
Tool and Process Monitoring
BK MIKRO
BK Mikro is typically used as a broken tool detection system but can also be used for many other applications such as object inspection, position recognition and checking for part defects. The selection of the scanner and controller for broken tool detection systems is mainly application based. Follow the links below to explore specific models or contact us with application questions about our broken tool detection systems.
-
product
ALD Research
Veeco’s ALD Research page is a hub for the latest thinking in atomic layer deposition. It brings together experimental data, modeling insights and collaborative breakthroughs that help engineers stay ahead of the curve. Whether exploring new chemistries or solving complex process challenges, this resource is designed to inform, inspire and accelerate thin-film innovation.
-
product
3.5mm Short Open Load Thru 4-in-1 Analyzer Calibration Kit
Fairview Microwave’s portable calibration kits consist of two models, both with a compact, lightweight, 4-in-1 design package. These short-open-load-through (SOLT) calibration kits feature precision 3.5mm connectors, have a 26.5 GHz calibration capability, gold plated short-open-load-thru and include a handy lanyard. These SOLT calibration kits have a phase deviation of +/-2 degrees maximum and return loss of 30 dB minimum and feature an impedance level of 50 Ohms nominal. They are ideal for telecommunications, military electronics, automotive, medical, aerospace and consumer electronics industries.
-
product
Air Data Calibration
Fluke calibration offers digital pressure monitors, air data calibrators and laboratory standards for air data pressure range calibrations. Each of these systems feature pressure ranges, measurement units and features specific to calibrate air data test sets and RVSM compliant air data instruments. Models include 2468 Ruska and ADCS-601 DHI primary level standards; 7750i Ruska air data controller/calibrator and RPM4-AD DHI reference pressure monitor.
-
product
LXI Reed Relay Matrix - Dual 64x8 Plugin, Direct Y Access, 6 Analog Buses
65-223-001
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Step Attenuator
RSC
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
product
Outdoor AGC Optical Node
SR814WA
Hangzhou Softel Optic Co., Ltd.
*SR814WA series of 1310nm optical relay station is a two-way optical connector with HFC network engineering experience and equipment development experience accumulate for many years by ourselves only for HFC two-way Broadband Network. This product is designed with full consideration of network topological structure.The building block system modularized structure is adopted in SR814 Series *Field Optical Work station. It has flexible configuration and convenient debugging, and solves engineering and technical problems of collecting noise with two-way return path network. And it meets the requirements of modern CATV business network security transmission with high reliability of FTTB (Fiber to the Building).*SR814WA and SR814WB Optical Workstation are four way independent output models; WR-8604HB and WR-7504HB Optical Workstation are two way independent output models.*SR814WA Optical Workstation is our latest flagship product. Advanced optical AGC control circuit adds to the part of optical receiving to ensure the input optical power as low as -9dBm.
-
product
Reference Meters
Whether standard or high precision, ThermoWorks handheld meters feature rugged housing and best-in class accuracy across a variety of temperature ranges. Choose from integrated systems or meters that accept multiple probes, single or dual channel meters, alarms or reference models. Perfect for BBQ or sous-vide applications, dairy processing and meat processing, pharmaceutical labs, concrete curing, health departments, and for line checks, critical control point management, and HACCP checklists.
-
product
Portable Electrical Management Systems
EMS-LCHW30
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model T360M
Teledyne Advanced Pollution Instrumentation
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.
-
product
SP2T RF Pin Diode Switches To 18 GHz
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
product
Grain Moisture Meter, Measure Moisture & Temperature Grains
Model KM 963 G
Kusam Electrical Industries Limited
“KUSAM-MECO” Grain Moisture Meter Model KM 963-G incorporates the latest technology for determining the moisture in grains. It complements the family of moisture meters for wood(KM 963) & Paper (KM-963P). It can determine the % moisture in Wheat, Paddy, Rice & Corn. The Instrument consists of sensor which senses the moisture in grains & a microprocessor computes the signal in % which is displayed on the LCD. It is very simple to operate.
-
product
RF Shielded Box
LTL A6001
LTL A6001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A6001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
DC Power Supplies
Asterion DC ASA Series
AMETEK Programmable Power, Inc.
The Sorensen™ Asterion® DC ASA Series is the newest addition to the Asterion platform of power testing solutions. The new ASA Series features three independent, isolated 600W channels for a combined 1800W total output power. The autoranging supplies feature expanded current and voltage range at the full output power level, enabling the ability to satisfy a wider testing need without requiring the purchase of additional models.
-
product
Industrial ATX Motherboard with 8th/9th Gen Intel® Core™ i9/i7/i5/i3 or Xeon® E Processors
IMB-M45
ADLINK IMB-M45 ATX industrial motherboard supports the 8th/9th Generation Intel Core i9/i7/i5/i3 and Xeon E3 processor in the LGA1151 package, and the Intel C246 chipset. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz ECC or non-ECC memory up to 128 GB in four DIMM slots.
-
product
PDS Rock Dumping and Placement Software
Teledyne PDS Rockdump provides the functionality tailored to rock dumping operations to carry out the job more efficiently. The operator has an instant overview of the rock dump vessel with the top views displaying the vessel outline and the slides. Information about the vessel, the design model, surveyed area and/or pipeline is shown in various views that are updated as soon as new data is available and during the rock dump.
-
product
ANSI Potential Transformer Burdens
The ANSI Potential Transformer Burden Model PB-96-ANSI is designed for loading the Voltage transformers during accuracy tests as per ANSI standard C57.13. The PB-96-ANSI is a dual input ANSI burden providing the inputs of both 120V & 69.3V. It can be used along with the ELTEL Automatic Instrument transformer Test Set. AITTS-98 to test VTs as per ANSI standards.
-
product
Primary Injection Test Set
T1000
T1000 primary injection test set is the model featured with light weight and 2 minutes continuous output time at 1000Aac.
-
product
Microcontrollers
Panasonic Industrial Devices Sales Company of America
Based on a rigorous analysis of embedded device software and system needs, the Panasonic AM1 (MN101C/MN101E/MN101L) and AM3 (MN103H/MN103S/ MN103L) Series signal a new concept in Microcomputer design. With 8-bit and 32-bit models that share a unified architecture, Panasonic Microcomputers combine high performance with low power consumption in a package that supports C-language programming for a fast, efficient development cycle. Since the instructions for MN103H/MN103S and MN101C/MN101E are respectively compatible with MN103L's and MN101L's, the programming data can be inherited to achieve efficient system development. Panasonic Microcomputers feature a single development environment and are suitable for a wide range of applications, including high-performance embedded controllers and key devices in multimedia hardware.
-
product
Signal Acquisition
277
The Model 277 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
product
3D Software
Geomagic Freeform
Geomagic Freeform is the best solution for the design and manufacturing of organic shapes, giving you the real sensation of clay modeling but with all the added benefits of digital design. Now combined with Artec’s precise 3D scanners, you can effortlessly capture a large variety of objects in high detail directly into Geomagic Freeform software in order to easily solve any design and manufacturing challenges.
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58721
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- Three or six multiband DDCs- One or two DUCs- Two or four 800 MHz 16-bit D/As- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Signal Amplifier
A10150
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
product
Sensors
Advanced Thermal Solutions, Inc.
ATS designs a range of sensors for more accurate measurement of air and surface temperatures and air velocities. The different models allow data to be obtained in many conditions, including tight spaces and narrow planes. ATS sensors work exclusively with our ATVS family of hot wire anemometer systems.
