Product

Non-contact Sheet Resistance /resistivity Measurement Instrument

EC-80

-

NAPSON Corp.

EC-80 - NAPSON Corp.

*Easy operation and compact design*Auto-measurement start by inserting a wafer under the probe*Easy set up to measurement condition by JOG dial*5 types of model for each measuring range

Product

4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System

TCR-600

-

NAPSON Corp.

TCR-600 - NAPSON Corp.

*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）

Product

O/E Converter

TIA-3000

-

Scitec Instruments Ltd

TIA-3000 - Scitec Instruments Ltd

The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.

Product

Signal Splitter

-

G Systems, l.p.

G Systems, l.p.

The Dynamic Signal Buffered Splitter protects sound and vibration sensor acquisitions from the unwanted effects of a parallel troubleshooting or diagnostic instruments. G Systems Dynamic Signal Buffered Splitter provides buffered and unbuffered outputs connected to the same signal input. Up to 16 sensors, typically accelerometers, proximity probes, microphones, and pressure transducers, may be connected to the 16 signal inputs.

Product

Probe Adapters

-

Teledyne LeCroy

Teledyne LeCroy

Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.

Product

Globe-Thermometer – PMV PPD WBGT

TP876.I

-

Senseca

TP876.I - Senseca

Globe-thermometer probe for measurement of radiant heat with ∅ 50mm. Accuracy according to ISO 7243 ISO 7726.

Product

Waterproof Meter with ATC Probe

CyberScan pH 600

-

Eutech Instruments

CyberScan pH 600 - Eutech Instruments

Cal-Due Alarm Prevents Out-dated Calibrations, while Set-Point Alarms warns when readings are outside set-point limits.

Product

Fault Finder for Electrical Wiring Open / Short Circuit

FF310

-

General Technologies Corp.

FF310 - General Technologies Corp.

42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.

Product

Electronic Circular Temperature Chart Recorder

-

DeltaTRAK

DeltaTRAK

The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.

Product

IntelliPoint RF - Loop Powered Level Switch

-

AMETEK Drexelbrook

AMETEK Drexelbrook

The IntelliPoint Loop Powered Two Wire provides a capacitance probe level switch with current output and “On-Board” self-diagnostics to ensure reliability and level sensing elements for a wide variety of temperatures, pressures, and materials.

Product

Digital Display Auto Circuit Tester

1676

-

Peaceful Thriving Enterprise Co Ltd

1676 - Peaceful Thriving Enterprise Co Ltd

This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.

Product

Temperature and Humidity Probe

T3313

-

COMET SYSTEM, s.r.o.

T3313 - COMET SYSTEM, s.r.o.

Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

Acute High Voltage Differential Probe, 50x/500x, 25MHz, 3500V

ADP5025

-

TEAM SOLUTIONS, INC.

ADP5025 - TEAM SOLUTIONS, INC.

*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation

Product

Production Parametric Probe Card

VC20TM Fab

-

Celadon

VC20TM Fab - Celadon

*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear

Product

Diode Power probe

-

COMM-connect

COMM-connect

The COMM-connect 3026 Diode based temperature compensated probe is designed for use with the COMM-connect range of Power Monitors. The probe will handle from 50µW to 100mW . Used with external couplers and the our measurement system application from 1W to 1MW, a high dynamic range can be configured. The 3026 Diode based probe gives excellent stable results along with the COMM-connect Power Monitor variants. This gives our customers a number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.

Product

Natural Ventilation Wet Bulb Probe

TP3204S

-

Senseca

TP3204S - Senseca

Natural ventilation wet bulb probe for long-lasting measurements.

Product

Temperature and Humidity Regulator

H3431-4

-

COMET SYSTEM, s.r.o.

H3431-4 - COMET SYSTEM, s.r.o.

Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.

Product

Adjustment Tool

PK1-5MM-131

-

Teledyne LeCroy

PK1-5MM-131 - Teledyne LeCroy

Adjustment tool for probes

Product

Field Probe Positioner

-

innco systems GmbH

innco systems GmbH

The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.

Product

Specific Heat Capacity

-

Cryogenic Ltd.

Cryogenic Ltd.

The heat capacity probe uses a miniature AC calorimeter to measure the heat capacity of samples weighing as little as one microgram. The AC technique employed is highly sensitivity and combined with the automated Cryogenic Software, is simple to use.

Product

Test Service Offerings

-

ASE Industrial Holding Co., Ltd.

ASE Industrial Holding Co., Ltd.

ASE provides a complete range of semiconductor testing services to our customers, including front-end engineering testing, wafer probing, final testing of logic, mixed signal, and memory semiconductors, and other test-related services. Our testing services employ technology and expertise that are among the most advanced in the semiconductor industry.

Product

Probe Card Analyzers

PB1500

-

Integrated Technology Corp.

PB1500 - Integrated Technology Corp.

The PB1500 is a low cost probe card analyzer system. It has the capability to perform all the tests done on the larger PB3600/6500 probe card analyzers, but at a lower cost for low pincount cards. A maximum of 1,280 channels may be configured in the PB1500 MUX system. The Precision Measurement Unit (PMU) has the same accuracy, repeatability and range as the larger analyzers. The repair process consists of selecting a failing probe, which moves it under the binocular microscope and positions a crosshair over the correct position for that probe.

Product

Ultrasonic Single Element Probes

SONOSCAN P

-

SONOTEC GmbH

SONOSCAN P - SONOTEC GmbH

The ergonomic straight beam probes of the SONOSCAN Series for Nondestructive Testing (NDT) comply with the European Standard DIN EN 12668-2. Our ultrasonic transducers are used to check metals, plastics and ceramic materials for discontinuities, such as cracks, inclusions, blowholes and other material flaws.