Product

Magnetic Flaw Detector

CDX-Ⅲ

-

Mitech Co., LTD.

CDX-Ⅲ - Mitech Co., LTD.

magnetic particle flaw detector is the self-designed magnetic participle flaw detector of MITECH CO.,LTD. With small size, light weight, easy operation, multifunction in one unit. The detector can equip A, D, E O four types of probes to realize the functions of magnetic clamp detection, electromagnetic yoke detection, cross magnetic yoke detection, ring detection. It is the necessary detector to do quality control, safety check, life evaluation in the fields of petrol, chemicals, metallurgy, shipbuilding, aviation, railway etc

Product

Test Probe

-

WIT Co., Ltd

WIT Co., Ltd

INGUN, which has earned tremendous trust and achievements from customers all over the world in terms of quality and durability , has a network of distributors in about 50 countries around the world, and has a product lineup of more than 20,000 types.

Product

Fine Pitch Test Probes

-

Equiptest Engineering Pte Ltd

Equiptest Engineering Pte Ltd

Micro probes allow very fine pitch testing ranging from 0.13mm to 0.35mm pitchLow Resistance, Low inductance, High FrequencyWide selection of plating options to optimize contact challenges and maximize probe lifeTri-temp applications – 55°C to 155°C

Product

O-E PROBE

-

OptCom Company, Ltd

OptCom Company, Ltd

O-E probe is the unit to convert optical signals to electrical signals. It can be connected to Oscilloscopes or data loggers via a BNC connector and monitor the conversion waveform. It can acquire the optical signal easily by just pointing the optical fiber probe at the light source. Recently, more and more light sources utilize optical modulation for next generation lighting such as LED. Acquiring the emission timing is required to measure the emission phenomenon of the light source. This O-E probe unit is the ideal tool for these tasks.

Product

Silicon Resistivity, PN type & Alarm Tester

HS-PSRT

-

HenergySolar

HS-PSRT - HenergySolar

It use Four Probe to test the resistivity and P/N type of wafers、ingots and all type of silicon materials.It can be used by Solar and Semiconductor industry.

Product

High 1.73 (49.00) - 8.00 (127.00) High Performance Lead Free Probe

LFRE-1I35-8

-

ECT

LFRE-1I35-8 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Rotating Bolthole Scanners

Nortec

-

Evident Scientific

Nortec - Evident Scientific

Olympus extensive line of high performance eddy current scanners is available for use with Nortec Eddy Current Flaw Detectors. With a wide range of features consisting of speed ranges from 600 to 3000 rpm, frequency ranges from 100 Hz to 6 MHz, multiple connector types, and multiple probe types, our scanners offer a full range of application solutions.

Product

Capacitance Detection Probe

Which Ender

-

Cirris Systems Corporation

Which Ender - Cirris Systems Corporation

By sensing capacitance the Which Ender identifies if a wire is connected to a contact. When the Which Ender's button is pressed, a tone is produced. If a contact is connected to a wire, this tone will drop in pitch when the probe tip touches the contact. The Which Ender is essential for locating opens, breaks, and unused pins in connections.

Product

POWER PROBE MAESTRO

PPTM01AS

-

Matco Tools

PPTM01AS - Matco Tools

*Connects with the new Power Probe Tek application for greater diagnostic functionality*The Maestro and Power Probe Tek App will be compatible to connect with a majority of diagnostic scan tools*Trace mode offers scope-like functionality*Stream and record visual traces of electrical issues found when diagnosing*DC voltmeter with the capability of applying battery supplied voltage or ground*AC voltmeter: TRMS, peak-to-peak/min/max, frequency, duty cycle*Resistance testing with a live or unloaded circuit*Fuel-injector test mode*Driver test for testing module drivers

Product

Needle Microprobe

MT-29/5HT

-

Physitemp Instruments

MT-29/5HT - Physitemp Instruments

Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.

Product

Linear Motion Tandem Transducer

-

Columbia Research Laboratories

Columbia Research Laboratories

The Columbia Model LMT-50 is a unitized rugged package consisting of tandem linear variable differential transformers (LVDT's) with probe assembly. The LMT-50 is designed so that the likelihood of a single failure affecting both output signals is extremely improbable. The model LMT-50 offers flight proven performance, even in the most severe environments.

Product

RF Voltage Probe

P-20 Series

-

Auburn Technology

P-20 Series - Auburn Technology

The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.

Product

2.0J Impact Hammer

CX-T20

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-T20 - Shenzhen Chuangxin Instruments Co., Ltd.

Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.

Product

Digital Inspector

DI-2000

-

Lightel Technologies, Inc.

DI-2000 - Lightel Technologies, Inc.

Many modern network issues can be traced to contaminated or damaged fiber optic connector endfaces. Lightel’s DI inspection probe series provides ergonomic, easy-to-use, and versatile inspection of the endfaces for fiber optic male and female, single and multi-channel connectors.

Product

Building Inspection Kit

MR160-KIT2

-

Teledyne FLIR

MR160-KIT2 - Teledyne FLIR

Troubleshoot moisture and building problems wherever you go with the FLIR MR160-KIT2. This kit features the MR160, a moisture meter with IGM™ to quickly target problem areas, as well as the C2, a full-featured, pocket-sized thermal camera designed for a wide range of building and electrical applications. The MR160’s integrated pinless sensor and external pin probe provide the flexibility to take either intrusive or non-intrusive measurements. The kit also includes the MR06 wall cavity probe for even greater functionality.

Product

High Performance Liquid Chromatograph Triple Quadrupole Mass Spectrometer

LCMS-8045

-

Shimadzu Corp.

LCMS-8045 - Shimadzu Corp.

Equipped with a heated ESI probe, the LCMS-8045 has the highest sensitivity in its class. The heated ESI probe, high-temperature heating block, desolvation line (DL) and drying gas, all act to promote desolvation and prevent contamination due to the penetration of liquid droplets into the MS unit. This improves the robustness, so reliable and high-accuracy data can be obtained over the long term. The LCMS-8045 also achieves the world's fastest scan speed (30,000 u/sec) and polarity switching speed (5 msec). These enable ultra-high-speed, high-sensitivity analysis. The excellent cost performance of this system is demonstrated in food safety, environmental analysis, and other quantitative analyses, it can be upgraded to the LCMS-8060.